Jobs By Abekus

Analog-designs Questions Set 73:

Quiz Mode

If V_GS = 0 V and V_DS = 2.5 V, then the drain current I_D is

15.96 mA

9.43 mA

10.45 mA

6.88 mA

Solution:

A reverse-biased p-n junction has a resistance of the order of few megohms (MΩ)

None of the above

ohms (Ω)

kilohms (kΩ)

megohms (MΩ)

Solution:

In which configuration is a Zener diode biased when used in voltage stabilization circuits?

Reverse breakdown region

Forward Bias Region

Both

Solution:

If the current gain (β) is unknown in an emitter-biased circuit, you cannot calculate the

emitter voltage

emitter current

base current

collector current

Solution:

If the differential voltage gain and the common mode voltage gain of a differential amplifier are 48dB and 2dB respectively then it’s common mode rejection ratio is

45dB

46dB

47dB

48dB

Solution:

When choosing the operating point (Q-point) for a bipolar junction transistor (BJT), which of the following factors are considered?

Power supply

Maximum transistor rating

All of these

AC and DC load

Solution:

In a phase shift oscillator, an RC network is used to get the required phase shift. As a forgetful student, you have forgotten to use a resistor, and thus, the resistive path has been shorted. What is the phase shift that would be seen at the output?

90 deg

45 deg

180 deg

60 deg

Solution:

Why is the reverse collector saturation current greater than the reverse saturation current in a transistor?

They are the same

It is an ideal condition

Leakage current flows through the junction and surface

It does not include avalanche multiplication current opposing the collector current

Solution:

At very high temperatures, extrinsic semiconductors become intrinsic because

drive in diffusion of dopants and carriers

band-to-band transition dominates over impurity ionization

impurity ionization dominates over band-to-band transition

band-to-band transition is balanced by impurity ionization

Solution:

In a current mirror circuit, the reference current (I_o) is 10 mA, and a MOSFET (M1) connected to the reference current source has dimensions (W/L)₁ = 6. The dimensions of MOSFET (M2) to which the reference current is copied have (W/L)₂ = 3. What is the current (I_x) flowing in MOSFET M2?

5 mA

2.5 mA

18 mA

12 mA

Analog-designs Questions Set 73:

If V_GS = 0 V and V_DS = 2.5 V, then the drain current I_D is

Solution:

A reverse-biased p-n junction has a resistance of the order of few megohms (MΩ)

Solution:

In which configuration is a Zener diode biased when used in voltage stabilization circuits?

Solution:

If the current gain (β) is unknown in an emitter-biased circuit, you cannot calculate the

Solution:

If the differential voltage gain and the common mode voltage gain of a differential amplifier are 48dB and 2dB respectively then it’s common mode rejection ratio is

Solution:

When choosing the operating point (Q-point) for a bipolar junction transistor (BJT), which of the following factors are considered?

Solution:

In a phase shift oscillator, an RC network is used to get the required phase shift. As a forgetful student, you have forgotten to use a resistor, and thus, the resistive path has been shorted. What is the phase shift that would be seen at the output?

Solution:

Why is the reverse collector saturation current greater than the reverse saturation current in a transistor?

Solution:

At very high temperatures, extrinsic semiconductors become intrinsic because

Solution:

In a current mirror circuit, the reference current (I_o) is 10 mA, and a MOSFET (M1) connected to the reference current source has dimensions (W/L)₁ = 6. The dimensions of MOSFET (M2) to which the reference current is copied have (W/L)₂ = 3. What is the current (I_x) flowing in MOSFET M2?

Solution:

Related Question Sets:

Related Topics:

Analog-designs Questions Set 73:

If VGS = 0 V and VDS = 2.5 V, then the drain current ID is

Solution:

A reverse-biased p-n junction has a resistance of the order of few megohms (MΩ)

Solution:

In which configuration is a Zener diode biased when used in voltage stabilization circuits?

Solution:

If the current gain (β) is unknown in an emitter-biased circuit, you cannot calculate the

Solution:

If the differential voltage gain and the common mode voltage gain of a differential amplifier are 48dB and 2dB respectively then it’s common mode rejection ratio is

Solution:

When choosing the operating point (Q-point) for a bipolar junction transistor (BJT), which of the following factors are considered?

Solution:

In a phase shift oscillator, an RC network is used to get the required phase shift. As a forgetful student, you have forgotten to use a resistor, and thus, the resistive path has been shorted. What is the phase shift that would be seen at the output?

Solution:

Why is the reverse collector saturation current greater than the reverse saturation current in a transistor?

Solution:

At very high temperatures, extrinsic semiconductors become intrinsic because

Solution:

In a current mirror circuit, the reference current (Io) is 10 mA, and a MOSFET (M1) connected to the reference current source has dimensions (W/L)1 = 6. The dimensions of MOSFET (M2) to which the reference current is copied have (W/L)2 = 3. What is the current (Ix) flowing in MOSFET M2?

Solution:

Related Question Sets:

Related Topics:

If V_GS = 0 V and V_DS = 2.5 V, then the drain current I_D is

In a current mirror circuit, the reference current (I_o) is 10 mA, and a MOSFET (M1) connected to the reference current source has dimensions (W/L)₁ = 6. The dimensions of MOSFET (M2) to which the reference current is copied have (W/L)₂ = 3. What is the current (I_x) flowing in MOSFET M2?