Jobs By Abekus

Hydraulics Questions Set 5:

Quiz Mode

The value of the coefficient of velocity is _____.

0.76

0.98

0.57

Solution:

Which fluid is commonly used as a manometric liquid?

Water

Mercury

Kerosene

Oil

Solution:

Which type of turbine is preferred for a water head range of 0 to 25 meters?

Pelton wheel

Kaplan turbine

Tube turbine

Francis turbine

Solution:

The available head of a Francis Turbine is 100 m. The velocity of the flow at the runner inlet is 15 m/s. Find the flow ratio.

0.33

0.45

0.67

0.89

Solution:

In which type of turbine are the turbine inlet whirl velocity and inlet jet velocity equal in magnitude?

Propeller turbine

Pelton turbine

Kaplan turbine

Francis turbine

Solution:

If a pipe with an end cap nozzle discharges a jet of water with velocity V, and the jet hits a plate moving towards the nozzle with velocity V/2, then the discharge of the jet hitting the plate would be:

0.5 Q

1.5 Q

2 Q

Solution:

A trapezoidal channel is 10.0 m wide at the base and has a side slope of 4 horizontal and 3 vertical. The bed slope is 0.002. The channel is lined with smooth concrete (Manning’s n = 0.012). The hydraulic radius (in m) for a depth of flow of 3.0 m is

20.0

3.5

3.0

2.1

Solution:

A 1:50 model of a spillway is to be tested in the laboratory. The discharge in the prototype spillway is 1000 m³/s. The corresponding discharge (in m³/s, up to two decimal places) to be maintained in the model, neglecting variation in acceleration due to gravity, is ____.

Solution:

The top width and depth of flow in a triangular channel are 4m and 1 m respectively. The measured velocities on centre line at the surface, 0.2 m and 0.8 m below the surface are 0.6 m/s and 0.4 m/s respectively. Using 2-point method of velocity measurement, the discharge (Q) in the channel in m³/s is,

1.4

1.2

1.0

0.8

Solution:

A short reach of a 2 m wide rectangular open channel has its bed level rising in the direction at a slope of 1 in 10000. It carries a discharge of 4 m³/sand it’s Manning’s roughness coefficient is 0.01. Flow is gradually varying. At a certain section in the reach, depth of flow was measured as 0.5 m. The rate of change of water depth, dy/dx at this section is ____. (use g = 10 m/s²) Round off to 4 decimal places

Hydraulics Questions Set 5:

The value of the coefficient of velocity is _____.

Solution:

Which fluid is commonly used as a manometric liquid?

Solution:

Which type of turbine is preferred for a water head range of 0 to 25 meters?

Solution:

The available head of a Francis Turbine is 100 m. The velocity of the flow at the runner inlet is 15 m/s. Find the flow ratio.

Solution:

In which type of turbine are the turbine inlet whirl velocity and inlet jet velocity equal in magnitude?

Solution:

If a pipe with an end cap nozzle discharges a jet of water with velocity V, and the jet hits a plate moving towards the nozzle with velocity V/2, then the discharge of the jet hitting the plate would be:

Solution:

A trapezoidal channel is 10.0 m wide at the base and has a side slope of 4 horizontal and 3 vertical. The bed slope is 0.002. The channel is lined with smooth concrete (Manning’s n = 0.012). The hydraulic radius (in m) for a depth of flow of 3.0 m is

Solution:

A 1:50 model of a spillway is to be tested in the laboratory. The discharge in the prototype spillway is 1000 m³/s. The corresponding discharge (in m³/s, up to two decimal places) to be maintained in the model, neglecting variation in acceleration due to gravity, is ____.

Solution:

Solution:

Solution:

Related Question Sets:

Related Topics:

Hydraulics Questions Set 5:

The value of the coefficient of velocity is _____.

Solution:

Which fluid is commonly used as a manometric liquid?

Solution:

Which type of turbine is preferred for a water head range of 0 to 25 meters?

Solution:

The available head of a Francis Turbine is 100 m. The velocity of the flow at the runner inlet is 15 m/s. Find the flow ratio.

Solution:

In which type of turbine are the turbine inlet whirl velocity and inlet jet velocity equal in magnitude?

Solution:

If a pipe with an end cap nozzle discharges a jet of water with velocity V, and the jet hits a plate moving towards the nozzle with velocity V/2, then the discharge of the jet hitting the plate would be:

Solution:

A trapezoidal channel is 10.0 m wide at the base and has a side slope of 4 horizontal and 3 vertical. The bed slope is 0.002. The channel is lined with smooth concrete (Manning’s n = 0.012). The hydraulic radius (in m) for a depth of flow of 3.0 m is

Solution:

A 1:50 model of a spillway is to be tested in the laboratory. The discharge in the prototype spillway is 1000 m3/s. The corresponding discharge (in m3/s, up to two decimal places) to be maintained in the model, neglecting variation in acceleration due to gravity, is ____.

Solution:

Solution:

Solution:

Related Question Sets:

Related Topics:

A 1:50 model of a spillway is to be tested in the laboratory. The discharge in the prototype spillway is 1000 m³/s. The corresponding discharge (in m³/s, up to two decimal places) to be maintained in the model, neglecting variation in acceleration due to gravity, is ____.