Jobs By Abekus

Design Questions Set 26:

Quiz Mode

Find the length of span if the pulley width is 800 mm.

860 mm

950 mm

900 mm

960 mm

Solution:

Which of the following is measured by the ABS function?

Wheel rotation

Torque

Temperature

Camber

Solution:

What is the misalignment tolerance of a Taper Roller bearing?

2 minutes of arc

3 minutes of arc

4 minutes of arc

5 minutes of arc

Solution:

The characteristics of the drive for crane hoisting and lowering are:

Smooth Movement

Precise control

Fast speed control

All of the above

Solution:

The flat ends of a boiler are prevented from bulging out and are strengthened by means of

connection of plates at right angles

welding

gusset stays

riveting

Solution:

Calculate the direct shear stress in the welds by ignoring torsional shear stress if P=8kN and thickness of weld is 5mm.

14.33N/mm²

12.33N/mm²

None of the listed

13.33N/mm²

Solution:

A 20-degree full depth involute profiled 19-tooth pinion and 37-tooth gear are in mesh. If the module is 5 mm, the center distance between the gear pair will be:

150 mm

280 mm

140 mm

300 mm

Solution:

If a solid shaft of 45 mm diameter is subjected to both a bending moment of 320 kN-mm and a torque of 160 kN-mm, calculate the maximum principal stress induced in it.

37.89 N/mm^2

40.01 N/mm^2

35.81 N/mm^2

29.73 N/mm^2

Solution:

A double riveted lap joint of 5 mm thick plates with 15 mm diameter rivets having a pitch of 60 mm. The tearing resistance of the plate, if the maximum possible tensile stress in the plate is 100 MPa, is?

20.5 N

22.5 N

20.5 kN

22.5 kN

Solution:

A mild steel rod of 12 mm diameter was tested for tensile strength with a gauge length of 60 mm. The following observations were recorded:

Final length = 80 mm; Final diameter = 7 mm; Yield load = 3.4 kN and Ultimate load = 6.1 kN. Calculate the ultimate tensile stress.

54.5 MPa

54 MPa

64 MPa

53.5 MPa

Design Questions Set 26:

Find the length of span if the pulley width is 800 mm.

Solution:

Which of the following is measured by the ABS function?

Solution:

What is the misalignment tolerance of a Taper Roller bearing?

Solution:

The characteristics of the drive for crane hoisting and lowering are:

Solution:

The flat ends of a boiler are prevented from bulging out and are strengthened by means of

Solution:

Calculate the direct shear stress in the welds by ignoring torsional shear stress if P=8kN and thickness of weld is 5mm.

Solution:

A 20-degree full depth involute profiled 19-tooth pinion and 37-tooth gear are in mesh. If the module is 5 mm, the center distance between the gear pair will be:

Solution:

If a solid shaft of 45 mm diameter is subjected to both a bending moment of 320 kN-mm and a torque of 160 kN-mm, calculate the maximum principal stress induced in it.

Solution:

A double riveted lap joint of 5 mm thick plates with 15 mm diameter rivets having a pitch of 60 mm. The tearing resistance of the plate, if the maximum possible tensile stress in the plate is 100 MPa, is?

Solution:

A mild steel rod of 12 mm diameter was tested for tensile strength with a gauge length of 60 mm. The following observations were recorded:

Final length = 80 mm; Final diameter = 7 mm; Yield load = 3.4 kN and Ultimate load = 6.1 kN. Calculate the ultimate tensile stress.

Solution:

Related Question Sets:

Related Topics:

Design Questions Set 26:

Find the length of span if the pulley width is 800 mm.

Solution:

Which of the following is measured by the ABS function?

Solution:

What is the misalignment tolerance of a Taper Roller bearing?

Solution:

The characteristics of the drive for crane hoisting and lowering are:

Solution:

The flat ends of a boiler are prevented from bulging out and are strengthened by means of

Solution:

Calculate the direct shear stress in the welds by ignoring torsional shear stress if P=8kN and thickness of weld is 5mm.

Solution:

A 20-degree full depth involute profiled 19-tooth pinion and 37-tooth gear are in mesh. If the module is 5 mm, the center distance between the gear pair will be:

Solution:

If a solid shaft of 45 mm diameter is subjected to both a bending moment of 320 kN-mm and a torque of 160 kN-mm, calculate the maximum principal stress induced in it.

Solution:

A double riveted lap joint of 5 mm thick plates with 15 mm diameter rivets having a pitch of 60 mm. The tearing resistance of the plate, if the maximum possible tensile stress in the plate is 100 MPa, is?

Solution:

A mild steel rod of 12 mm diameter was tested for tensile strength with a gauge length of 60 mm. The following observations were recorded: Final length = 80 mm; Final diameter = 7 mm; Yield load = 3.4 kN and Ultimate load = 6.1 kN. Calculate the ultimate tensile stress.

Solution:

Related Question Sets:

Related Topics:

A mild steel rod of 12 mm diameter was tested for tensile strength with a gauge length of 60 mm. The following observations were recorded:

Final length = 80 mm; Final diameter = 7 mm; Yield load = 3.4 kN and Ultimate load = 6.1 kN. Calculate the ultimate tensile stress.